The Next Generation of Ionic Plasma Thrusters (BSI MARK 2)

Three quick notes - 1) Thank you to Morning Brew, 2) Let's address diameter differences. The diameter on my friend's thruster was around 7 cm. The BSI is 12 cm, which is moving a large volume of air. 3) BSI Mark 3 is currently underway. Thanks for watching!

Another few angles you might try: 1) Changing the pulse waveform: Shorter rise times should result in much greater transfer of energy to the air, and having a dynamic rise time that adjusts with incoming air velocity might be even better. Humidity and ambient air pressure variation will also require the dynamic rise times for greater efficiency. Additionally, staggering the timing between the stages might increase efficiency as well. 2) Curved wires: requires dielectric spacers to retain equidistant wire spacing. Concentric counter facing half-rings could maximize your area of charge, resulting in an increase to the total air-charge transfer. Changing the angle between stages so that the air begins to take on an angular moment as well may increase thrust. 3) Inter-stage wiring: Presently, your conical intakes allow for passive air intake. This could be changed to an active intake area as well, with an additional few HV leads, resulting in additional charged air.

While you have already tested and optimised spacing between the anode and cathode for a single stage, i think you should really adjust each stage in a stack individually. The air molecules entering at different velocities might impact how far they need to be apart.

I would recommend 2 things. 1: Remove all axillary air intakes to remove all the additional air entering the system making it more turbulent and thus less effective at each stage. 2: if you want increased thrust and air speed you need to focus all that air, so play around with a diameter reducing cone after the last stage, you will need to play around with different lengths and diameters to find one that gives you what you are looking for 👍 Best of luck, it's been fun watching what you have been working on.

I have no idea what any of this means but peeps like this deserve support.

You can use Bernoulli's Principle. Instead of placing the individual thruster back-to-back, try to put them side-by-side, and then constrict the output of the thruster system with the help of a nozzle, that might increase the airflow's speed.

You could put the whole thing in a housing, with slits at angles off-set from each other. That way the side intakes aren’t competing with each other for wind as much. I think having the stages be different sizes, and the housing go from large to small, along with the stages, could make use of the effect where the velocity of the fluid increases as you hold flow rate steady & decrease the area through which the fluid travels.

I found your video about the plasma thrusters and as a technician I was fascinated. Great work!! I want to share my idea to you for increasing the thrust in a three stage model: Use slightly different stages: With a lower distance between anode : cathode in the first stage, and an increased distance in second stage and an once more an increased distance in the third flow. Greetings from a farmer's boy from Austrian mountain area.

You have to try putting a convergent nozzle on this. I’m not sure how much static pressure it’s generating but there must be some, and a nozzle would convert that into more speed. It would also have the added bonus of slowing down upstream flow so it has more time to interact with the extra stages, like you saw in the fan test

As I think someone mentioned below, you could try making each consecutive ring slightly smaller, only by a few percent at each stage. That way you would introduce 'venturi' like effects to increase the speed of airflow, whilst also adding energy at each ring. Great video, thank you.

Have you considered reducing the diamater of each stage to tighten the airflow? Also we need to see these thrusters actually push something.

That's a beautiful build Jay, I feel this has a great future soon even for commercial aircrafts❤❤

I'm very happy to see this kind of friendly competition in this new field! This is how we make progress

Nice one Jay. Not only a beautiful design, but you have proved that patience and persistence has paid off. For every problem there is always a solution. Thanks for sharing. Also thanks to Alex, Charles & Joel for their input. Rog from Wales 🏴󠁧󠁢󠁷󠁬󠁳󠁿. 😃👍

Should definitely look into using generative design to get the weight of the wing down more! Amazing work!

This is literally the first time heard of ionic thruster. I'm freaking out! This is future tech is here what wow omg

You should try inverting the polarity of the second ring (emitter and collector). Once passing through the first ring, the air is no longer neutral, it's ionised, thus the second ring's emitter will actually repel it. By inverting the polarities of the second ring, you may experience the boost you are looking for.

Phd student here. Really awesome work! If you ever want to build one of those NASA thrusters I can help. My background is in Hall thrusters and know a bit about electrospray as well. Keep up the great work!

Está buenísimo, es el futuro de los motores, ojalá lo puedas desarrollar aún más!!! Suerte

Thus video is absolutely awesome. As a student of Advanced Astrophysics, Quantum Physics and other related subjects including Plasma Physics, I would be very tempted to actually build something like this as I have always been into things like Plasma Physics etc. I will keep you updated as to how I get on and hopefully I'll see some results within the next few months once I've designed and built my first ionic thruster. Keep up the totally awesome work you're doing.