3 Ways to Connect Subwoofer LFE to Audio Receiver | Pre Amp & Speaker Wire Level | Beginner Guide

Just jumped off a video that was terrible. Here the presenter gets right to the point. Very simple, no preaching, no losing track of where he was going like the last video I started but quit.

Thanks for this finally figured out how properly wire an old Kenwood system together.. everything sounds great, cheers😎👌

Great video! Fixed a lot of my problems all in this one video. I never understood in the back of the receiver where it says the right side and left side. Because the components are right behind the receiver so when it says right-to-left I don't understand what it's telling me and where does right begin or left 🤷‍♂️

Great video my demon ave-2803 sub out went and I thought my sub was useless until I found this work around

I like how you explain each step. It is real.

Thank you for the content. well executed! . I appreciate the time you put into this 😁🤙

What a very great tutorial. Excellent detailed advice that I did find very helpful. Thank you. Just a note, the work you were doing on stripping the wire, I find the better way is to use a lighter to heat/burn the part of the insulation you want to strip off, then simply blow on it then while it's warm, pull that piece off with your fingers or a pliers. Takes 4 seconds. Way faster and no need to purchase a wire stripper.

Great, thank you, now, my new receiver is 5.1 and my previous receiver is 7.1 I don't want to loose the height speakers. I'm going to try this way hooking them to my Audio Source 10 (220watt)sub. I do hope this works, thanks again.

Hello, could I use the 2 subwoofer pre-out to run some front speakers and also surround sperakers through a power amp, or are those pre-outs specific to sub woofer only? The recievers with more pre outs are getting hard to find in my area and are pretty high dollar.

Thanks for the video. Could you help me with best way to connect my Klipsch SL100 to my Yamaha RXA-800. Thanks

Hi. I have the Onkyo tx-sr444 and I’m unable to find an Onkyo subwoofer for it. Can I use any other brands wired subwoofer with it? If yes, what should I take in consideration when choosing one? I will appreciate your advice because I don’t know much about Sound Systems.

Can anyone help! Pulling my hair out! I have a pioneer sc lx av revciver which doesn't seem to send a signal to my sub (I've plugged the sub into the other channels and it plays like a speaker with vocal so sounds terrible) but just doesn't work on subwoofer. Played with the settings and changed speakers to small but it then doesn't display subwoofer settings. I changed them back to small and I can then turn the subwoofer to "on" and I also tried "plus" mode but nothing. Tried it in direct mode, advanced surround and all the other modes. I don't know what else I can try. Appreciate any help!

Hi, I have an Onkyo TX-RZ840 and that I've just bought and I want to connect to my external amplifier Marantz MM7055 5 channels. I tried to activate the pre-amps on my receiver, but it's not working, I mean, there are no additional amplification and also I lost my center channel

Great info video! Thank you for answering exactly what my question was.

could i use a rca to speaker wire cable to run my subwoofer that uses speaker wire?

Just trying to get a prostudio 15 in a sub box should I just connect it to a reciver

Thank you so much, you made my day.

So I have this same subwoofer Klipsch R-12SW and I buy speakers Argon Audio Fenris A4. Subwoofer have LFE Input and speakers have only 2x rca output. So I can use cable type Y? Cable with 2x Rca to 2x Rca speakers output and 1x rca to LFE subwoofer input?

my sub is wired and the receiver I'm upgrading to, the sub output isn't wired. Can I use banana plugs to connect the wired sub to the receiver?

Hi is there anyway I can use an old sub to a soundbar without sub ?